GE MULTILIN SR FEEDER MANAGEMENT RELAY NEW VAC. General Electric P5-G5-S5-HI-AR-E. General Electric GE MULTILIN SR GE MULTILIN SR FEEDER MANAGEMENT RELAY NEW VAC, WITH CASE. General Electric P5-G5-S5-HI-AR-T-H. General Electric GE. Find great deals for GE Multilin Feeder Management Relay Sr Shop with confidence on eBay!.
|Published (Last):||23 October 2015|
|PDF File Size:||10.5 Mb|
|ePub File Size:||2.71 Mb|
|Price:||Free* [*Free Regsitration Required]|
Load shedding schemes based on voltage and frequency elements Back-up protection for transmission lines, feeders and transformers Distributed Generation DG interconnect protection. A failure to respond to an open or close signal in a programmed time can be used to generate an alarm. When the measured quantity exceeds the pickup level, the relay can trigger an alarm or signal an output.
Oscillography A block of configurable volatile memory can be used for recording samples of the AC input voltages and current, and the status of logic inputs and output relays. EnerVista 8 Series Setup Software provides automated setting file conversion. An alarm is also generated if the relay detects that the supervisory trickle current is not present.
No need to disconnect any of the field wiring.
Breaker Conditions The relay calculates the per-phase wear sr75 the breaker contacts to establish a threshold. A block of configurable volatile memory can be used for recording samples of the AC input voltages and current, and the status of logic inputs and output relays. This product is under last-time buy. Two analog input level monitoring elements and two rate-of-change elements are available. Simply remove the terminal blocks and then remove the SR chassis from the panel. This memory can be configured between the ranges of two to 16 blocks with 16 to power frequency cycles of data respectively.
With the new 8 Series Retrofit Kit users are able to install the Feeder Management System without modifying existing cutouts and wiring, and without any drawing changes or re-engineering time.
GE Multilin 750 Feeder Management Relay Sr750
Any external quantity may be monitored via an auxiliary current input. Event Recording The relay captures and stores the last events, recording the time, date, cause, and system parameters.
This easy to use relay provides comprehensive protection functions for feeders and back up protection for bus, transformers and transmission lines at a reduced product life cycle sr50. Insert the new 8 Series Retrofit chassis into the switchgear and simply plug-in the old terminal blocks – there is no need to make any cut-out modifications or push and pull cables.
The relay captures and stores the last events, recording the time, date, cause, and system parameters. Fault Locator The relay uses captured data to calculate the type, distance to and the impedance of the fault. Indicators Twenty LEDs indicate relay status, system status, and trip and alarm conditions. A 40 character display allows access to setpoints, actual values, sr7550 diagnostic messages generated by a trip or alarm condition. Convenient COMTRADE and Sequence of Events viewers are an integral part of the Setup software included with every relay, to carry out postmortem event analysis to ensure proper protection system operation.
Once completed, a graphical report is provided to verify and call out any specific settings that may need attention.
The VT failure feature monitors each phase of input voltage, generating an alarm and sending the programmed output signals when a failure is detected. Events may be recorded selectively by category, so that only events of interest are recorded. The relay uses captured data to calculate the type, distance to and the impedance of the fault. VT Failure The VT failure feature monitors each phase of input voltage, generating an alarm and sending the programmed output signals when a failure is detected.
About Grid Solutions GE’s Grid Solutions business serves customers globally with over 17, employees in approximately 80 countries. Trace memory recording can be triggered by operation of selected features or logic inputs. A rear Ethernet port is also available as an optional feature. The front panel port allows easy local computer access.
General Electric GE MULTILIN SR CASE NEW
The amount of pre-event data recorded is set by the user. Grid Solutions helps enable utilities and industry to effectively manage sr70 from the point of generation to the point of consumption, helping to maximize the reliability, efficiency and resiliency of the grid. When the breaker maintenance threshold is exceeded the relay can trigger an alarm.
Traditionally, retrofitting an existing relay has been a challenging, time consuming task often requiring re-engineering, new drawings, panel modifications, re-wiring and re-testing.
User Interface Various user interfaces facilitate operation of the The can display 30 user-selected messages during keypad inactivity.
Display A 40 character display allows access to setpoints, actual values, and diagnostic dr750 generated by a trip or alarm condition. As an alternative, please refer to the relay. The relay calculates the per-phase wear on the breaker contacts to establish a threshold. Records of the last 10 faults are stored.