epD‐BfS‐ () Environmental Product  Schweizerischer ingenieur‐ und Architektenverein (SiA). () Merkblatt energieausweis für Gebäude gemäß Sn en und Sn en zurich.  Schweizerischer . Flash point: > 21° C „Beschichtung auf Zink und verzinktem Stahl“ from Bundesausschuss Farbe und Sachwertschutz (BFS) according to Merkblatt 5 of BFS. Flash point: > 21° C. Solid substance: approx. 55% Zinc and galvanized surfaces are to be prepared according to Merkblatt 5 of. BFS. Clean the surfaces to be painted and remove dirt of all kinds, including dust, mortar droppings, and similar.
|Published (Last):||5 April 2018|
|PDF File Size:||1.14 Mb|
|ePub File Size:||15.86 Mb|
|Price:||Free* [*Free Regsitration Required]|
Use scaffolding-nets, if necessary.
Deeper damages up to 20 mm should be repaired with Histolith-Renovierspachtel. Cap-elast Phase 1 and Cap-elast Phase 2: An additional priming coat of CapaGrund Universal must be applied. Measurement and Modelling of Travel Behaviour.
Clean soiled substrates and algae infested surfaces carefully by water-jet using low pressure, in compliance with the regulations. Disposal Materials and all related packaging must be disposed of in a safe way in accordance with the full requirements of the local authorities.
Facades in special climatic conditions high degree of moisture or subjected to a higher influence of atmospheric exposure: Coating of such surfaces must be considered as a risk for which we cannot accept responsibility, since even after the most thorough treatment the efflorescence may recur. Transport Planning – Theory and Models.
Sylitol® NQG: Caparol
Protected against algal and fungal attack. Thus all relevant copper surfaces must be protected against oxidation. In case of direct reworking, all traces of additives must be pre-wetted and completely removed after having respected a short reaction time. Apply one priming coat of AmphiSilan-Putzfestiger.
The quality of the dried mermblatt will not be affected by these changes. Clean stable bsf coatings by mechanical means or use high-pressure water jet, in compliance with the regulations.
In case of direct reworking, all traces of additives must be pre-wetted and completely removed after a short reaction time. The obtained results show that the combination of a mode-choice model with MATSim is a promising approach to set up a feedback-enabled transport simulation.
Cap-elast Riss-Spachtel: Caparol
If other cleaning methods are used washing, wire brushing, hosing with waterprime with AmphiSilan-Putzfestiger. Provide for an evenly absorbent substrate to achieve uniform surfaces without shade variations. Plasto-elastic filler for filling cracks in render and brickwork. Axhausen, Kay W Dispose containers with residues of liquid product via waste collection point accepting old paints and enamels.
Thus all relevant copper surfaces must be protected against oxidation. Surfaces with Salty Efflorescence: Ensure good ventilation during use and drying. Checnet Coupling human and ecological networks for sustainable landscape and transport planning. Do not clean by mechanical means.
Then use Capatox or FungiGrund and allow to dry thoroughly. The results contribute to the understanding of residential location choice and have implications for urban planning and policies that seek to reduce commuting. Possibly a second finishing coat may be necessary.
ThermoSan NQG Nespri-TEC
Note Do not apply under a glaring sun on heated surfacesduring strong wind, fog, high relative humidity, or imminent rain or frost. Given well-designed constraints on top of the choice model, a good fit with the reference data is achieved. Fibre-reinforced, plasto-elastic surfacer for leveling uneven substrates before applying subsequent Cap-elast coatings.
Modeling multi-modal traffic in cities using the 3D Macroscopic Fundamental Diagram. Cap-elast Phase 2 and Phase 2-W: