Amercoat Chemical Resistant Lining. Product Data/. Application Instructions. • High Solids, high performance epoxy novolac also defined. Amercoat – Download as PDF File .pdf), Text File .txt) or read online. This Safety Data Sheet is prepared in accordance with Annex II to Regulation ( EC) No. / AMERCOAT CHEMICAL LINING CURE.
|Published (Last):||3 January 2017|
|PDF File Size:||9.81 Mb|
|ePub File Size:||7.4 Mb|
|Price:||Free* [*Free Regsitration Required]|
Mechanically fastened KEE membrane roofing system. Swinger pump by AirTech with 1 fluid hose to pump outlet affixed with a pole gun with external atomizing air. Amercoat is compatible over most types of properly applied and tightly adhering coatings, however, a test patch is recommended to confirm compatibility. Material temperature must be maintained at 60 to 90 F at the time of application for application below 50 F.
Swelling may occur with prolonged contact 7. Multiple coats may be required to achieve proper film build and hiding with roller application. Qmercoat products are intended for buyers with amerrcoat knowledge and skills to evaluate the suitability of Hi-Temp s products for buyer s intended use.
Rev Page 1 of 3. Apply Dimetcote 9VOC as soon as possible to prevent the blasted qmercoat from rusting.
Pacific Southwest Coatings – Pacific Southwest CoatingsPacific Southwest Coatings
Additional Information Paint Prepared by: Waterborne Shop Primers- Why. Avoid exterior painting late amercoxt the day or when dew or condensation are likely to form or if rain is expected. For aged inorganic zinc coatings, spot blast rusted areas in accordance with the surface preparation instructions before touching up with Dimetcote When blasting is not practical, Amercoat 68HS or Dimetcote H may be used for repair. Triarch products work well over a variety of substrates, both for interior and exterior settings.
Use standard conventional spray guns with a mm nozzle orifice psi fluid pressure. Mechanical surface preparation should expose sub-surface voids and provide a surface profile equivalent to 80 grit sandpaper or coarser. Color matches are approximate. Remove any dry spray and solvent wipe. Do not apply under freezing conditions. An agitated pressure pot is recommended.
Spread and trowel to the desired finish using typical concrete finishing tools. Variations in the application environment, changes in procedures of use, or extrapolation of data may cause unsatisfactory results. PPG may modify the information contained herein at any time as a result of practical experience and continuous product development.
Do not prime stainless steel with a zinc primer. A test patch is recommended. Clean and treat all exposed anodized architectural. Slowly incorporate glass flake additive under agitation over minutes to ensure the glass flake is thoroughly mixed. When using glass flake additive a spray tip size of X. PanelTack is solvent- and isocyanate.
Amercoat 253 pdf
Separate regulators for air and fluid pressure are recommended. Surface should be free of any oil, grease, embedded chemicals, laitance, water repellants, previous sealants, wmercoat release compounds, and effluoresence. Ensure any dry spray is removed.
Back roll with a saturated roller to work into block porosity. Do not apply over galvanizing, zinc coatings, or concrete. Tideguard may receive water contact immediately after application; however, the wet coating should be protected from splashing action which could remove the film while it is still wet.
Prepare surface in accordance with application instructions for the specific primer being used. For corrosion resistant service, use of an approved corrosion resistant primer is necessary. Lightly abrasive blast with fine abrasive to produce a uniform amefcoat dense anchor profile of mils in accordance with SSPC SP Colors will change on exposure to sunlight.
Strain through a mesh screen. Surface temperature 40 F to F 5 C to 54 C Surface temperature must be at least 5 F above the dew point temperature. Care and Maintenance for Wood Flooring Care and Maintenance for Wood Flooring The finishing technology used for Tarkett wood floorings makes them the best choice for easy maintenance. CertainTeed warrants More information. Shelf Life Liquid and Powder 18 months from date of manufacture when stored indoors in the original unopened container.
Thin the second coat with Amercoat thinner or Amercoat thinner.
Protective Coatings Product Catalog AMERCOAT. A PPG brand – PDF
The A component is the same for Amerlock and Amerlock 2. Applicable over surface treatments such as MIL-C Alternately, lightly abrasive blast with fine abrasive to produce a uniform and dense anchor profile of mils. Thoroughly remove dust or abrasive residue before touch-up. Consult Hi- Temp for alternate and approved primers.
Alternately, power tool clean to uniformly abrade the surface or lightly abrasive blast with a fine abrasive to produce a uniform and dense anchor profile of mils in accordance with SSPC SP